Surface charging behaviors of electrocatalytic interfaces with partially charged chemisorbates

The surface charge is a key concept in electrochemistry. Mathematically, the surface charge is obtained from a spatial integration of the volume charge along a particular direction. Ambiguities thus arise in choosing the starting and ending points of the integration. As for electrocatalytic interfaces, the presence of chemisorbates further complicates the situation. In this minireview, I adopt a definition of the surface charge within a continuum picture of the electric double layer. I will introduce surface charging behaviors of firstly ordinary electrochemical interfaces and then electrocatalytic interfaces featuring partially charged chemisorbates. Particularly, the origin of nonmonotonic surface charging behaviors of electrocatalytic interfaces is explained using a primitive model. Finally, a brief account of previous studies on the nonmonotonic surface charging behavior is presented, as a subline of the spectacular history of electric double layer.     

Multivariate optimization and comparison between conventional extraction (CE) and ultrasonic-assisted extraction (UAE) of carotenoid extraction from cashew apple

Carotenoids are an essential component of cashew and can be used in pharmaceuticals, cosmetics, natural pigment, food additives, among other applications. The present work focuses on optimizing and comparing conventional and ultrasound-assisted extraction methods. Every optimization step took place with a 1:1 (w:w) mixture of yellow and red cashew apples lyophilized and ground in a cryogenic mill. A Simplex-centroid design was applied for both methods, and the solvents acetone, methanol, ethanol, and petroleum ether were evaluated. After choosing the extractor solvent, a central composite design was applied to optimize the sample mass (59–201 mg) and extraction time (6–34 min). The optimum conditions for the extractor solvent were 38% acetone, 30% ethanol, and 32% petroleum ether for CE and a mixture of 44% acetone and 56% methanol for UAE. The best experimental conditions for UAE were a sonication time of 19 min and a sample mass of 153 mg, while the CE was 23 min and 136 mg. Comparing red and yellow cashews, red cashews showed a higher carotenoid content in both methodologies. The UAE methodology was ca. 21% faster, presented a more straightforward composition of extracting solution, showed an average yield of superior carotenoid content in all samples compared to CE. Therefore, UAE has demonstrated a simple, efficient, fast, low-cost adjustment methodology and a reliable alternative for other applications involving these bioactive compounds in the studied or similar matrix.     

不同退火条件对PEALD制备的Ga2O3薄膜特性的影响

利用等离子增强原子层沉积技术(PEALD)在c面蓝宝石衬底上制备了氧化镓(Ga₂O₃)薄膜,研究了退火气氛(v(N₂)∶v(O₂)=1∶1(体积比)、空气和N₂)及退火时间对Ga₂O₃薄膜晶体结构、表面形貌和光学性质的影响。研究结果表明,退火前的氧化镓处于亚稳态,不同退火气氛下退火后晶体结构发生明显改变,而且退火气氛中N₂比例增加有利于Ga₂O₃重结晶。在N₂气氛下退火达到30 min,薄膜结构已由亚稳态转变成择优取向的β-Ga₂O₃。而且表面形貌分析表明,退火30 min后表面形貌开始趋于稳定,表面晶粒密度不再增加。另外实验样品在 400~800 nm的平均透射率几乎是100%,且光吸收边陡峭。采用N₂气氛退火,对于富氧环境下沉积的Ga₂O₃更利于薄膜表面原子迁移,以及择优取向Ga₂O₃重结晶。     

Surface Tension Effect on Harmonics of Rayleigh-Taylor Instability

Using the method of the parameter expansion up to the third order, explicitly investigates surface tension effect on harmonics at weakly nonlinear stage in Rayleigh-Taylor instability (RTI) for arbitrary Atwood numbers and compares the results with those of classical RTI within the framework of the third-order weakly nonlinear theory. It is found that surface tension strongly reduces the linear growth rate of time, resulting in mild growth of the amplitude of the fundamental mode, and changes amplitudes of the second and third harmonics, as is expressed as a tension factor coupling in amplitudes of the harmonics. On the one hand, surface tension can either decrease or increase the space amplitude; on the other hand, surface tension can also change their phases for some conditions which are explicitly determined.     

Structure and Mechanical Stability of Epoxy Modified Polyurethane Foam Under Heat and Stress

A series of phenolic epoxy resin (PEP) modified polyurethane foams (PUF) were prepared via an in-situ polymerization, one step process. It was found that the epoxy modified PUF foam exhibited a perforated network structure with larger cell size, higher open cell porosity and enhanced ovality compared with pure PUF. With increasing content of PEP, the tensile strength, elongation at break and low temperature modulus of PUF decreased. A single T_g was observed for PEP modified PUF, indicating that the two component phases of the polyurethane-epoxy were miscible. With increasing PEP content, the T_g of PUF shifted slightly to higher temperature, tan δ_max dropped to lower values, and the retention value of the storage modulus at ?20 and ?10?°C increased. For pure PUF, the cell walls degraded and the structure became disordered after aging under heat and stress, while for PUF/20wt%PEP, the degradation degree was obviously reduced, and an orientation of the cells along the stress direction and a density increase was observed. During aging at 200?°C, the retention of the mechanical properties of PUF/20wt% PEP was much higher than that of pure PUF, and it showed superior stability under heat and stress, attributed to incorporation of the thermally resistant oxazolidone rings and benzene rings in the PU backbones, the highly cross-linked networks of the polyurethane-epoxy systems and the obvious orientation of the cells under stress.     

旋涂法制备WO3薄膜电致变色性能

"智能窗"大规模推广顺应可持续发展潮流,三氧化钨(WO_3)是生产"智能窗"的一种重要电致变色材料,但调控WO_3薄膜电致变色性能机制仍待进一步研究。采用旋涂法制备WO_3薄膜,重点研究了溶液浓度和旋涂次数对调控WO_3薄膜电致变色性能的影响。通过表面轮廓仪测量薄膜厚度,X射线衍射(XRD)测量薄膜结晶情况,原子力显微镜(AFM)和扫描电子显微镜(SEM)分析薄膜表面形貌,光谱仪测量薄膜初始态、着色态和褪色态的透射率。实验结果表明,随着溶液浓度增加(0. 2～1. 0 mol/L),薄膜厚度从9. 7 nm增加到33. 3 nm,透射率调制能力从0%提升到37. 0%;多次旋涂薄膜厚度线性增长,线性拟合优度(R~2)达0. 98,5次旋涂后透射率调制能力达51. 3%。改变溶液浓度和旋涂次数都是调控薄膜透射率调制能力的有效手段,精准调控薄膜透射率调制能力对设计不同应用场景的电致变色器件具有重大意义。     

Behavior of poly(ε-caprolactone)-based diblock copolymers in a bulk state and in solution

Abstract

A series of amphiphilic MOPEO-b-PCL copolymers (DBCs), based on biocompatible methoxypoly(ethylene oxide) with M_n=4.5?kDa and poly(ε-caprolactone) of a variable chain length, was synthesized by an anionic ring-opening block copolymerization. The structural investigations, performed by DSC and WAXS methods, revealed the microphase separation in DBC bulk structure and the existence of separate amorphous regions and microcrystalline domains of MOPEO and PCL blocks. Spectrophotometry and SLS were used to study the self-assembling of DBC macromolecules in selective dioxane/aqueous solution and to determine the main micellization parameters (CMC and -ΔG°). The DBC micelles morphology and their specific aggregation in mixed solvent were shown.     

Damage characteristics and surface description of near-wall materials subjected to ultrasonic cavitation

For the analysis of ultrasonic cavitation erosion on the surface of materials, the ultrasonic cavitation erosion experiments for AlCu4Mg1 and Ti6Al4V were carried out, and the changes of surface topography, surface roughness, and Vickers hardness were explored. Cavitation pits gradually expand and deepen with the increase of experiment time, and Ti6Al4V is more difficult to erode by cavitation than AlCu4Mg1. After experiments, the cavitation damage characteristics such as the single pit, the rainbow ring area, the fisheye pit, and some small pits were observed, which can be considered to be induced by a single micro-jet impact, ablation effect caused by the high temperature, micro-jet impingement with a sharp angle, and multibeam micro-jets coupling impact or negative pressure in the local area produced by micro-jet impact, respectively. The surface roughness and Vickers hardness of the material increase slowly after rapid growth at different points in time as the experiment time increases. With the increase of the ultrasonic amplitude, both of them first increase and then decrease after the ultrasonic amplitude is greater than 10.8 μm. The increases in surface roughness and Vickers hardness tend to decrease as the viscosity coefficient increases. Ultrasonic cavitation can cause submicron surface roughness and increase surface hardness by 20.36%, so it can be used as a surface treatment method.     

Ultrasound irradiation effect on morphological and adsorptive properties of a nanoscale 3D Zn-coordination polymer and derived oxide

In this work, Zn-based coordination polymer [Zn₂(1,3-bdc)bzim₂]_n was successfully synthesized by the sonochemical method using a 13 mm probe-type ultrasound operating at 20 kHz and amplitudes of 30, 40 and 50% corresponding to an acoustic power of 5.5, 8.6, and 10.3 W, respectively. Additionally, a sample was prepared by the slow-diffusion method for comparison. The samples were characterized by FTIR, PXRD, SEM, and BET techniques. The influence of the time and sonication amplitude on the yield of the reaction, crystallite size, and morphology were also studied. It was found that the sonochemical method provided the desired product in 83.9% within 20 min of sonication using the highest level of sonication amplitude. Moreover, this approach resulted in regular, controlled morphology, smaller particles, and higher surface area of the Zn-sample and derived oxide, than the slow diffusion method. The samples prepared by different methodologies were tested for the adsorption of BTEX (benzene, toluene, ethylbenzene, and xylenes) components in six different systems, and the uptakes were quantified by ¹³C NMR spectroscopy. Both samples showed excellent adsorption of benzene, 119.8 mmol/g, and 88.1 mmol/g, for the coordination polymers prepared via the sonochemical and slow-diffusion methods, respectively, corresponding to 63.9%, and 46.9%. These results are in agreement with the non-polar surface of these samples.     

限域量子态调控研究

电子、激子和声子等量子态在固体中的行为早已被人们所熟知. 然而，当体系的尺寸只有纳米量级的时候，已有的固体理论常常不能适用，需要新的低维物理理论的建立. 我们系统研究了低维体系限域量子态（包括电子、激子和声子）的行为对环境、应力、压力及光的响应和性质的调控. 较早认识到低维体系之显著的表面-体积比对量子态性质调控之有效性，系统地揭示了低维体系的一系列由表面和应力决定的新颖性质，证明了低维体系的表面和应力效应同量子限域效应同等重要. 本文概况了如下五个方面的结果：（1）一种使用应力效应调控电子能带结构的方法和（2）一种使用表面效应调控电子能带结构的方法（这两个方法都可将低维体系能带从间接能隙调控至直接能隙能带结构）；（3）一种低维体系表面掺杂方法，该方法将在低维体系掺杂中取代传统方法；（4）量子点表面诱导的光致异构现象；（5）基于表面自催化半导体低维结构的形成机理. 希望我们的研究工作有助于促进低维体系在光电子、纳电子、环境、能源、生物和医学等领域的应用.